06/01/2026
Lake City Speedway
June 13
Points Race 4
2828 Green Rd
Cades, Sc 29560
Gates Open @ 9am
Practice @ 11am
Gate Fees
$15 adults
$5 Kids 12&under
If need parking text Justin
Parking & Questions text
843-304-3952 Justin
843-742-6315 Matt
ALL MONEY GUARANTEED
❌❌❌We are only racing 20 karts in mains events if over 20 entries no consi❌❌❌
Clone Heavy(375) $300
Clone Medium(350) $200
Clone Lite(325) $100
Pro Clone Super (425) $250
Super Heavy(425) $100
Flathead Heavy (375) $150
Sr Stock 35+(375) $100
Sr Stock 45+(375) $100
Amateur Clone Medium(350) $100
Amateur Clone Heavy(375) $100
Ducar Medium(350) $100
Ducar Heavy(375) $150
Amateur Predator Medium(350) $100
Amateur Predator Heavy(375) $100
Pro Jr 1 $100
Jr 1(275/8-10yrs old/black plate) 100%
Pro Jr 2 $125
Jr 2(290/10-12yrs old/yellow plate) 100%
Pro Jr 3 $150
Jr 3 (325/12-15yrs old/blue plate) 100%
Red Plate (250/5-8yr old/Gear rule 15-68/Tire rule 34”) 100%
Entry Fees(includes transponder)
$5 points fee & $5 insurance xtra
$35- $100&$150
$40-$200&$250
$45-$300
Protest Is $200 & $100 to accept!
**Amateur Classes (A main 100 to win/ B main 50 to win)
PREDATOR RULES (for amateur)
Can't turn over 5100 on the track. Must run an approved tach. M-3, M-4, M-5, M-6, Alphno 6.
There is no free spinning governor check but it has to be there.
All parts must appear stock from 5 feet away. No changing parts between engines. Ducar 212 all Ducar parts. Non Hemi 212 Predator parts on Non Hemi Predator. Hemi 212 Predator parts on a Hemi Predator.
Open clutch and gear nothing smaller than a 53 rear gear.
Dyno Cams Ducar Rules
1. Engine must be factory rated Ducar 212cc and run in box stock configuration. All parts must be stock OEM production parts unless otherwise specified in these rules. No alteration, cutting, grinding or machining of any parts. No sandblasting, tumbling or polishing of any kind. This is strictly prohibited. All parts are subject to be checked by a known stock part if in question. No reading between the lines. If it is not specifically mentioned in these rules, then it MUST remain stock.
2. Gas: 87 octane pump gas only. (Track to supply test sample.)
3. Block: Stock OEM Ducar 212 block with no machining allowed with the exception of cylinder clearance. Maximum bore size 2.758” 0 piston pop up allowed.
4. Cylinder Head: No machining permitted on gasket surface and absolutely no porting of any kind. Maximum intake valve head diameter 1.062” +- .005” Maximum exhaust valve size .946” +- .005” Minimum depth from gasket mating surface to combustion chamber between valves it .485” +- .010” (for reference only.) The seats must be stock and can have the 3 angles of 30/45/60 as from the factory. However, you may not attempt to excessively sink the valves in an effort to increase airflow. Stock OEM graphite style head gasket only. Minimum .042” thickness. No sealer.
5. Piston & Rings: Stock OEM dished piston with valve relief on exhaust side only. Maximum size 2.7565” measured at the bottom of the skirt. Stock OEM rings. No altering of the rings allowed, especially the oil ring.
6. Rod: Stock OEM cast connecting rod only. Rod may be honed for oil clearance only. No rounded or broken edges. No billet rods allowed.
7. Crankshaft: Stock unaltered OEM crankshaft. Governor gear must be installed in stock location. Max stroke 2.163 +-.010”
8. Flywheel: Engine must run PVL aluminum die cast flywheel only. No cast iron OEM flywheels. Must utilize stock unaltered timing key. Stock OEM unaltered ignition coil.
9. Camshaft: Must run stock OEM camshaft. Base circle size .865” +.010 - .005” Maximum Intake lift .225 Maximum In duration at .050” = 210 Maximum In duration @ .200 = 75 Maximum Ex lift .232” Maximum Ex duration @ .050” = 212 Maximum Ex duration @ .200” = 84 All checks to be taken at the push rod.
10. Valve Train: Maximum valve spring wire diameter .079” Stock OEM springs must be used. (15lb @ .850” reference only) Valve seal allowed on intake side only. No shims allowed. Stock OEM push rods must be used with a maximum length of 5.825” +.010” Stock unaltered lifters and spring retainers to be used. No lightweight components.
11. Carburetor: Stock OEM Ruixing carb only. Carb must be completely stock. No machining of any kind. Maximum venturi .615” and minimum venturi size .608” Carb bore maximum .750” Stock E-tube with a maximum of 20 holes. 1.092” minimum length and minimum outside diameter of .154” .066” maximum hole through the E-tube. Butterfly minimum .037” Minimum throttle shaft .115” Minimum screw length .305” Phenolic spacer must remain stock. Maximum pilot jet size .018”(.019”no-go)and must use both o-rings. Maximum main jet size .029” (.030” no-go)
12. Air Box: Stock OEM air box must be used and in stock unaltered form only. Air must enter through the air filter only. Any open unused holes must be plugged. Stock OEM air filter with foam sock must be used.
13. Muffler: Stock OEM muffler in unaltered form must be used. If any doubts about the integrity of the muffler should arise, simply cut the muffler in two, to determine legality by comparing to known stock muffler.
14. Governor: Governor gear, arm and linkage must remain intact and functional.(As of MARCH 1st, 2024 competitors may utilize the DUCAR OEM rev limiting ignition coil(Part # 212-1260R) as an alternate to the stock OEM governor. You may remove the governor assembly completely and plug holes, leave governor in place and wire in the open position or leave the governor assembly in stock form. Regardless of method chosen, the engine still cannot free rev over 5500 rpm max.) Track may require engine to be free revved on the stand to a certain RPM to determine if governor is properly functioning. (5500 rpm max for example) It has been our findings that some engines surge and some will not. We do not require the surge because in stock form the engine will perform best at 5000 rpm or less. However, this will be left entirely up to the race promotor/tech.
15. Gas Tank: Stock tank should be removed and an auxiliary tank mounted in the floor pan should be used. A top plate and fuel pump are allowed with the pump be pulsed off the valve cover only. (Track Option) Utilize stock OEM tank with the vent tube unplugged and up to 4 - 1/8” holes in the fuel cap for venting.
16. Low oil shutoff can be disconnected. No taping or decals added to the recoil in an attempt to block off air.
17. Chain guard, throttle linkage, top plate and fuel pump are the only aftermarket parts allowed on the engine.
18. There is no longer a claimer rule. The engine in question must be protested by a competitor or subject to tech by the track if the promotor/tech deems necessary. The protest will be $200 and acceptance fee will be $100.
19. If there is any doubt as to the legality of any part on a Ducar 212 engine, the competitor has the right to file a protest with the track/official. The part in question can then be shipped to DynoCams for review. Please include contact information for the promotor and we will contact the promotor with our findings on the legality of the part in question in a timely mannere
